Types of flame is very essential factor during oxy acetylene welding. In the welding the appropriate shape, size, type and condition are need to be kept in mind for the controlled  operation of oxy acetylene welding.

welding flames are classified on the basis of the ratio of oxygen and acetylene gases used while combustion takes place, As the combustion are done after mixing two gases. The flame contains two cones, the inner cone and the outer envelope. The type of flame can be recognized by the size and the colour of these cones. There are three types of welding flames.

1. Carburizing flame or reducing flame
2. Neutral flame
3. Oxidizing flame
Types of Flames in Oxy-Acetylene Welding

Carburizing flame

In the carburizing flame the ratio of the gases are to be taken such that the gas containing carbon (Acetylene) will be in more amount and oxygen will be in less amount. Between the inner cone and the outer envelope there will be a feather which generates due to the combustion of carbon containing element. This type of flame is used when hard and brittle welding is required because the carbon causes hardness in the material. The outer envelope is longer than that of the neutral flame. This flame is useful for carburizing or surface hardening process in the metals. The flame also avoids the oxidation of the material because all the oxygen is consumed during comdustion. The length of the total flame is biggest amongs all the three types of flame.It is also known as redusing flame

Neutral flame

Equal proportion of acetylene and oxygen is to be taken for combustion to produce a neutral flame in oxy acetylene welding. The length of the total flame is shorter than that of carburizing flame and longer than that of in oxidizing flame. As the amount of fuel and oxygen is same so the complete combustion of fuel will take place and there will be no or very small chemical effect on the material. The neutral flame is desired where the need of no oxidising and no carburizing occurs. This type of flame is used for the welding of low Carbon Steel, copper, aluminium cast iron. In this type of flame the inner cone can be seen clearly. Outer envelope is darker than that of inner cone.

Oxidising flame

This flame generates when the amount of oxygen is more than acetylene in the mixing proportion for combustion. The length of total flame is shorter amongst all the three types of flames. The inner cone will be pointed. The blue colour is darker than both the carburizing and oxidizing flame. The oxidation of the material takes place due to excess amount of oxygen. The temperature of the flame will be highest amongst all the three type of flame. Due to the oxides, the appearance of the welding can be bad and there are chances of welding defects.

Conclusion

These are the types of flames for gas welding. The selection of flame depends on the type of material to be weld and the required properties after welding. Amount of gases to be mixed is controlled by the hoses levers situated on the welding torch from where the gases will pass. As per the requirement the type of flame can be generated.

8 comments:

  1. wow thanks. there is some good content here

    ReplyDelete
  2. Enter your comment...good work I love this

    ReplyDelete
  3. This comment has been removed by the author.

    ReplyDelete
  4. This comment has been removed by the author.

    ReplyDelete
  5. All things being equal, on the off chance that you are needing to learn, you can begin with a couple of basic procedures.Welding safety blog

    ReplyDelete
  6. Thanks for picking out the time to discuss this, I feel great about it and love studying more on this topic. It is extremely helpful for me. Thanks for such a valuable help again. https://laserhispeed.com/uv-laser-marking-machine/

    ReplyDelete
  7. Looking for Industrial Laser Cutting Materials ? Then we are the best for you, who suit your expectations. We have huge experience on this field. We are 100% dedicated to find you cheap Industrial Laser Cutting Materials.
    You can buy Industrial Laser Cutting Materials here and here are numberius clients buy our products. We are provide only high quality Industrial Laser Cutting Materials with always customers support.

    If you want to know more, Please check out here - https://dxtech.com/10-industrial-laser-cutting-materials/

    ReplyDelete
  8. The CNC plasma flame cutting machine is specially designed for sheet metal cutting. It has the characteristics of high automation, high efficiency, easy operation, and long service life. Want to find a suitable flame cutting machine? Click to view more plasma flame cutting machine information: https://forsuncnc.com/cnc-plasma-cutter/

    ReplyDelete